|
|
Chinese manufacturer flow meter with the type of vortex used of
Industrial
Quick Detail:
1. Accurancy:1.0%
2. Repeatability:0.03%
3. Normal size:DN15-DN.300
4. Power supply:+12VDC to 36VDC or 3.6V lithium battery
5. Display:LCD screen
6. Medium temperature:-10 to +55C
7. Output:4-20mA or pulse output.
8. Protocal:RS485 protocal or Hart Protocal
9. Connection:flange connection or clamp connection
10. Housing materials:304 strainess steel,probe:316L
11. Pressure:PN16Mpa PN2.5Mpa ,PN40Mpa PN6.4Mpa
Description:
As flow passes a bluff body in the flow stream vortex meter, the
vortices create low and high pressure zones behind the bluff body,
or shedder bar. Our vortex flow meters are designed with a
piezoelectric crystal sensor to detect the pressure exerted by the
vortices on the velocity sensor. The sensor converts these “pulses”
into electrical signals which are then converted to a frequency by
the meter`s electronics allowing the volumetric flowmeters to
calculate the volumetric flow rate to be determined. Additionally,
each vortex flowmeter we design features an all welded sensor
design which creates a robust sensor and to minimize potential
leaks.With the addition of the optional integrated temperature and
pressure sensors, the flow meter can then calculate and output the
mass flow rate as well as volumetric flow, temperature, pressure,
and density.
Smart vortex flowmeter is mainly used for measuring flow of
industrial pipeline fluid, such as gas, liquid and steam, etc. It
has little pressure loss, broad span range and high accuracy. It is
not under influence of density, pressure, temperature and viscosity
when measuring volumetric flow. It has no movable mechanical parts
with high reliability and little maintenance.
Its characteristics are no pressure loss, no moving parts and no
maintenance. Though it is similar to Electro Magnetic Flowmeter the
one advantage Vortex Meter has over EMF is the medium need not be
conductive as in the case of EMF. This flowmeter adopts
piezoelectric sensor, has high reliability, and works with in –200C
to +2500C. It gives standard analogue signal (4 ~ 20mA) or Digital
pulse signal outputs. It is compatible with digital systems like
Computer, DCS Systems, Dataloggers, etc.
If you have any questions Please contact me at any time . SKYPE :
susan86861 .
Applications:
Vortex Flowmeter is used to measure the flow of liquids, Gases or
Steam in pipelines.
Specifications:
Application range | (1)Gas;(2)Liquid;(3)Steam |
Primary measured value | Flow Rate |
| Volume flow. |
Modular construction | The measurement system consists of a flow sensor and a signal
converter. |
| N Type: Pulse output without local display |
A Type: 4-20mA Output without local display | |
B Type: Local Display; Lithium Battery Power | |
C Type:Local Display;24VDC Power;4-20mAOutput; | |
Pulse Output | |
Connection | Flange:DN15-DN300 |
Wafer:DN15-DN300 | |
Measurement Ratio | Standard–10:1 |
| Flow conditions similar toEN29104 |
Medium:Water/Gas | |
Electrical conductivity:≥300μS/cm | |
Temperature:+10...+30°C/+50...+86°F | |
Inletsection:≥10DN | |
Operating pressure:1bar/14.5 psig | |
Flow Meter Accuracy | For Liquid:1.0%ofrate |
For Gas and Steam:1.5% of rate | |
| T1 Level:-20...+70°C |
T2 Level:-20...+250°C | |
T3 Level:-20...+350°C | |
Ambient temperature | Standard(with aluminum converter housing): -10…+55°C |
Storage temperature | -20 …+70° |
Pressure | |
| DN200-DN300:PN10 |
DN100-DN200:PN16 | |
DN15-DN80:PN25 | |
Other pressures on request | |
JIS | 1/2”...8":10K |
1/2”...8":10K | |
Installation | Take care that flow sensor is always fully filled |
For detailed information see chapter"Cautions for Installation" | |
Flow direction | Forward |
Arrow on flow sensor indicates flow direction. | |
Inlet run | ≥10DN |
Outlet run | ≥5DN |
Sensor housing materials | SS304 |
Other materials on request | |
Converter Housing | Standard: polyurethane coated die-cast aluminum |
Process connections | |
Flange EN1092-1 | DN15...300 in PN6...25 |
ASME | 1/2”…12"in150 lb RF |
JIS | 1/2”…12”in10...20K |
Design of gasket surface | RF |
Wafer | DN15…DN300 |
Competitive Advantage:
Our products have competitive price advantage.As flow passes a bluff body in the flow stream vortex meter, the
vortices create low and high pressure zones behind the bluff body,
or shedder bar. Our vortex flow meters are designed with a
piezoelectric crystal sensor to detect the pressure exerted by the
vortices on the velocity sensor.
Industrial Chinese 304 strainess steel Vortex Flow Meter , Pressure PN16Mpa PN2 Images |